3.6, CISCO

3.6

3.6, CISCO

[ Pobierz całość w formacie PDF ]
1What is the default setting for the mode LED on a switch?*** STATFDUPUTIL100PORT2An old workstation has been replaced with a new one. The workgroup switch is not learning the MAC address of the new workstation. A network technician has verified that a static MAC address is not configured on the attached switch port. Which commands can the technician issue at the switch CLI to further troubleshoot the problem? (Choose two.)*** Switch# show port securitySwitch# show versionSwitch# show startup-config*** Switch# clear mac-address-tableSwitch# reloadSwitch# delete flash:vlan.dat3Which files must be deleted in order to completely remove an existing configuration from a Cisco 2950 switch? (Choose two.)flash:c2950-c3h2s-mz.120-5-3.WC.1.binrunning-configVLAN.bin*** startup-configc2950-c3h2s-mz.120-5-3.WC.1.dat*** VLAN.dat4Which type of cable is used to connect to the console port on a switch?a crossover cablea patch cable*** a rollover cablea straight-thru cable5A workstation on a switched Ethernet LAN is to be upgraded with a new Fast Ethernet NIC. What should be done to ensure that the workstation will be able to gain access to the network?delete the configuration file from the switch and reload IOS*** deactivate port security on the port until the new host has connected to the networkremove the host from the the management VLAN until the new MAC address has been learned by the switchdelete the VLAN.dat file from flash and reboot the switchconfigure the attached switch port for full-duplex mode6What does an amber system LED indicate about a Catalyst switch? (Choose two.)*** The switch has power.The switch has passed POST and is working properly.*** The switch has failed POST.The switch is going through POST.The switch is in the process of initializing its ports.7What must be done in order to initiate the password recovery procedure on a Catalyst 2900 series switch?Rename the Flash file.Enter the setup program by deleting the switch configuration file and rebooting the switch.*** Hold down the MODE button during switch startup.Wait for the STAT LED to turn green while holding down the Break key.Hold down the Ctrl-Break keys during switch startup.8From which switch command mode can the configure command be used?configuser EXEC*** privileged EXECcommand EXECflash9Which form of switch command-line help displays a list of keywords and arguments that are associated with a command entered at the CLI prompt?CLI help*** command syntax helpkeyword helpword help10What is the name of the series of tests that execute every time a switch is powered on?RPSbootstrap*** power-on self testsystem STATpre-boot11A new policy for disaster recovery requires copying all critical network configurations and operating systems to a backup server that will be stored offsite. Which command will create a backup of the switch IOS image on the server?Switch# copy tftp NVRAMSwitch# copy running-config tftp*** Switch# copy flash tftpSwitch# copy IOS tftpSwitch# copy tftp flashSwitch# copy NVRAM tftp12The network administrator shown in the graphic is connected to Switch3 over Ethernet. The administrator needs to verify configuration settings on the newly installed Switch2. What conditions need to be met in order for the administrator to access Switch2 with a web browser? (Choose three.)*** complete IP addressing configured on Switch2*** Privileged EXEC mode password configured on Switch2hostname configured on Switch2management VLAN password set*** HTTP service activated on Switch2adminstrator host connectivity to the Switch2 management VLAN13Which protocol is used to copy a new IOS image to a Catalyst switch during the upgrade procedure?HTTPTelnet*** TFTPTTYIOS14What color is the System LED if the switch fails the POST?*** ambergreenredwhiteoff15Although the backup configuration file on a Catalyst 2950 switch has been erased, it is found that VLANs are still configured in the switch. What must be done to clear the configured VLANs?*** The vlan.dat file must be erased and the switch reloaded.The switch flash memory must be purged and the switch rebooted.The vlan.cfg file must be renamed and IOS restarted.Each VLAN needs to be deleted individually and the configuration saved.The switch needs to be restarted, because the old running configuration is still in memory.16How can a switch be configured to prevent unauthorized hosts from access to a network? (Choose three.)*** Host MAC addresses can be statically assigned to each switch port.Layer 2 access control lists can be used to prevent unauthorized network access.*** Unused ports can be shutdown.Passwords and usernames can be set for each Ethernet switch port.Unused switch ports can be assigned to the management VLAN.*** Port security can be activated to allow only the host with the first MAC address learned on a port to access the network.17Which switch command mode should always be password protected?User CommandUser ConfigUser EXECUser Privileged*** Privileged EXEC18Which options are available when setting the action to be taken when a port security violation occurs on a switch port? (Choose two.)log-allowreturn*** trap*** shutdownpoison19Which commands can be used to change from Global Configuration mode to Privileged EXEC mode? (Choose three.)*** Ctrl+zdisable*** end*** exitlogout20What are the recommended HyperTerminal configuration settings for establishing a console session between a switch console port and PC COM port? (Choose three.)*** 9600 bits per second192000 bits per secondhardware flow control*** flow control Xon/Xoffeven parity*** no parity21Which methods can be used to perform the initial configuration of a new switch? (Choose two.)copy a configuration from a FTP server*** type commands manually after entering the Privileged EXEC mode*** enter the System Configuration dialogTelnet to a local server to copy a configuration fileconnect to the switch using a web browser22An administrator is using the switch help facility to find the command elements available to the configure command. What would the user type at the command prompt to display the next set of arguments available in the syntax for this command?Switch# c?Switch# c ?Switch# configure?*** Switch# configure ?23How long will a host MAC address remain in the address table of a switch after the host has been turned off or moved to another device?30 seconds180 seconds*** 300 seconds30 minutes24After powering up a switch, the network technician notices that the system LED is amber. What can the technician assume? (Choose two.)The switch is negotiating full or half-duplex mode.The switch has completed negotiating 10 or 100 Mbps speed.*** The POST has failed.The boot sequence is in process.*** A fatal error has occurred.The switch is operating properly and is ready for service.25A group of hosts has been connected to a new Fast Ethernet switch. Which of the following statements describe this newly created LAN, if the new switch has not yet been configured? (Choose three.)*** The hosts will negotiate 10 Mbps or 100 Mbps bandwidth with the switch, as required by their NICs.The hosts will be in separate broadcast domains.*** All of the hosts will be in the same VLAN.Hosts with 10 Mbps NICs will be unable to communicate with the network.*** All of the hosts should be able to send and receive ARP messages from each other.All of the hosts connected by Ethernet can manage the switch over Telnet or HTTP.When the copy tftp flash command is used to upgrade the IOS on a switch, which symbol indicates that the image was copied successfully?e**** !s# [ Pobierz całość w formacie PDF ]

Linki

: 3.3.3.4 Lab - Użycie Wireshark do obserwacji ruchu w sieci, Studia, Semestr 4, sieci komputerowe - cisco

: 3.0.Final, CISCO